Makita Drill MODEL 6019D User Manual

Cordless Driver Drill  
Equipped with Electric Brake  
MODEL 6019D  
I N S T R U C T I O N M A N U A L  
WARNING:  
For your personal safety, READ and UNDERSTAND before using.  
SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE.  
w w w. m a k i t a t o o l s . c o m  
 
3. Keep bystanders, children, and visitors  
away while operating a power tool. Distrac-  
tions can cause you to lose control.  
shoes, hard hat, or hearing protection must  
be used for appropriate conditions.  
Tool Use and Care  
Electrical Safety  
12. Use clamps or other practical way to  
secure and support the workpiece to a  
stable platform. Holding the work by hand or  
against your body is unstable and may lead  
to loss of control.  
4. A battery operated tool with integral bat-  
teries or a separate battery pack must be  
recharged only with the specified charger  
for the battery. A charger that may be suit-  
able for one type of battery may create a risk  
of fire when used with another battery.  
13. Do not force tool. Use the correct tool for  
your application. The correct tool will do the  
job better and safer at the rate for which it is  
designed.  
5. Use battery operated tool only with specif-  
ically designated battery pack. Use of any  
other batteries may create a risk of fire.  
14. Do not use tool if switch does not turn it  
on or off. A tool that cannot be controlled  
with the switch is dangerous and must be  
repaired.  
Personal Safety  
6. Stay alert, watch what you are doing, and  
use common sense when operating a  
power tool. Do not use tool while tired or  
under the influence of drugs, alcohol, or  
medication. A moment of inattention while  
operating power tools may result in serious  
personal injury.  
15. Disconnect battery pack from tool or  
place the switch in the locked or off posi-  
tion before making any adjustments,  
changing accessories, or storing the tool.  
Such preventive safety measures reduce the  
risk of starting the tool accidentally.  
7. Dress properly. Do not wear loose cloth-  
ing or jewelry. Contain long hair. Keep  
your hair, clothing, and gloves away from  
moving parts. Loose clothes, jewelry, or long  
hair can be caught in moving parts.  
16. Store idle tools out of reach of children  
and other untrained persons. Tools are  
dangerous in the hands of untrained users.  
17. When battery pack is not in use, keep it  
away from other metal objects like: paper  
clips, coins, keys, nails, screws, or other  
small metal objects that can make a con-  
nection from one terminal to another.  
Shorting the battery terminals together may  
cause sparks, burns, or a fire.  
8. Avoid accidental starting. Be sure switch  
is in the locked or off position before  
inserting battery pack. Carrying tools with  
your finger on the switch or inserting the bat-  
tery pack into a tool with the switch on invites  
accidents.  
18. Maintain tools with care. Keep cutting  
tools sharp and clean. Properly maintained  
tools with sharp cutting edge are less likely to  
bind and are easier to control.  
9. Remove adjusting keys or wrenches  
before turning the tool on. A wrench or a  
key that is left attached to a rotating part of  
the tool may result in personal injury.  
19. Check for misalignment or binding of  
moving parts, breakage of parts, and any  
other condition that may affect the tool’s  
operation. If damaged, have the tool ser-  
viced before using. Many accidents are  
caused by poorly maintained tools.  
10. Do not overreach. Keep proper footing  
and balance at all times. Proper footing and  
balance enable better control of the tool in  
unexpected situations.  
11. Use safety equipment. Always wear eye  
protection. Dust mask, non-skid safety  
3
 
20. Use only accessories that are recom-  
mended by the manufacturer for your  
model. Accessories that may be suitable for  
one tool may create a risk of injury when  
used on another tool.  
tenance performed by unqualified personnel  
may result in a risk of injury.  
22. When servicing a tool, use only identical  
replacement parts. Follow instructions in  
the Maintenance section of this manual.  
Use of unauthorized parts or failure to follow  
Maintenance instructions may create a risk of  
shock or injury.  
SERVICE  
21. Tool service must be performed only by  
qualified repair personnel. Service or main-  
SPECIFIC SAFETY RULES  
USB022-2  
DO NOT let comfort or familiarity with product (gained from  
repeated use) replace strict adherence to cordless drill safety  
rules. If you use this tool unsafely or incorrectly, you can suffer  
serious personal injury.  
1. Hold tool by insulated gripping surfaces  
when performing an operation where the  
cutting tool may contact hidden wiring.  
Contact with a livewire will also make  
exposed metal parts of the tool liveand  
shock the operator.  
5. Hold the tool firmly.  
6. Keep hands away from rotating parts.  
7. Do not leave the tool running. Operate the  
tool only when hand-held.  
8. Do not touch the drill bit or the workpiece  
immediately after operation; they may be  
extremely hot and could burn your skin.  
2. Be aware that this tool is always in an  
operating condition, because it does not  
have to be plugged into an electrical out-  
let.  
9. Some material contains chemicals which  
may be toxic. Take caution to prevent  
working dust inhalation and skin contact.  
Follow material supplier safety data.  
3. Always be sure you have a firm footing.  
4. Be sure no one is below when using the  
tool in high locations.  
SAVE THESE INSTRUCTIONS  
WARNING:  
MISUSE or failure to follow the safety rules stated in this  
instruction manual may cause serious personal injury.  
4
 
SYMBOLS  
USD301-1  
The followings show the symbols used for tool.  
V .......................volts  
....................no load speed  
n
˚
...................direct current  
.../min................revolutions or reciprocation per  
minute  
IMPORTANT SAFETY INSTRUCTIONS FOR  
CHARGER & BATTERY CARTRIDGE  
USC001-3  
1. SAVE THESE INSTRUCTIONS - This man-  
ual contains important safety and operat-  
ing instructions for battery charger.  
6. To reduce risk of damage to electric plug  
and cord, pull by plug rather than cord  
when disconnecting charger.  
2. Before using battery charger, read all  
instructions and cautionary markings on  
(1) battery charger, (2) battery, and (3)  
product using battery.  
7. Make sure cord is located so that it will  
not be stepped on, tripped over, or other-  
wise subjected to damage or stress.  
8. An extension cord should not be used  
unless absolutely necessary. Use of  
improper extension cord could result in a  
risk of fire and electric shock. If extension  
cord must be used, make sure:  
3. CAUTION - To reduce risk of injury, charge  
only MAKITA rechargeable batteries  
marked on the charger label. Other types  
of batteries may burst causing personal  
injury and damage.  
a. That pins on plug of extension cord  
are the same number, size, and shape  
as those of plug on charger;  
4. Do not expose charger to rain or snow.  
5. Use of an attachment not recommended  
or sold by the battery charger manufac-  
turer may result in a risk of fire, electric  
shock, or injury to persons.  
b. That extension cord is properly wired  
and in good electrical condition;  
c. That wire size is at least as large as  
the one specified in the table below.  
Table 1: RECOMMENDED MINIMUM AWG SIZE FOR EXTENSION CORDS FOR BATTERY CHARGERS  
Length of Cord (Feet)  
AWG Size of Cord  
25  
18  
50  
18  
100  
18  
150  
16  
9. Do not operate charger with damaged  
damaged in any way; take it to a qualified  
serviceman.  
cord or plug - replace them immediately.  
10. Do not operate charger if it has received a  
11. Do not disassemble charger or battery  
sharp blow, been dropped, or otherwise  
cartridge; take it to a qualified serviceman  
5
 
when service or repair is required, Incor-  
rect reassembly may result in a risk of  
electric shock or fire.  
14. Young children should be supervised to  
ensure that they do not play with the bat-  
tery charger.  
12. To reduce risk of electric shock, unplug  
charger from outlet before attempting any  
maintenance or cleaning. Turning off con-  
trols will not reduce this risk.  
15. If operating time has become excessively  
shorter, stop operating immediately. It  
may result in a risk of overheating, possi-  
ble burns and even an explosion.  
13. The battery charger is not intended for  
use by young children or infirm persons  
without supervision.  
16. If electrolyte gets into your eyes, rinse  
them out with clear water and seek medi-  
cal attention right away. It may result in  
loss of your eyesight.  
ADDITIONAL SAFETY RULES FOR CHARGER &  
BATTERY CARTRIDGE  
1. Do not charge Battery Cartridge when  
temperature is BELOW 10°C (50°F) or  
ABOVE 40°C (104°F).  
(3) Do not expose battery cartridge to  
water or rain.  
A battery short can cause a large current  
flow, overheating, possible burns and  
even a breakdown.  
2. Do not attempt to use a step-up trans-  
former, an engine generator or DC power  
receptacle.  
6. Do not store the tool and Battery Car-  
tridge in locations where the temperature  
may reach or exceed 50°C (122°F).  
3. Do not allow anything to cover or clog the  
charger vents.  
4. Always cover the battery terminals with  
the battery cover when the battery car-  
tridge is not used.  
7. Do not incinerate the Battery Cartridge  
even if it is severely damaged or is com-  
pletely worn out. The battery cartridge can  
explode in a fire.  
5. Do not short the battery cartridge:  
8. Be careful not to drop, shake or strike bat-  
(1) Do not touch the terminals with any  
tery.  
conductive material.  
9. Do not charge inside a box or container of  
any kind. The battery must be placed in a  
well ventilated area during charging.  
(2) Avoid storing battery cartridge in a  
container with other metal objects  
such as nails, coins, etc.  
SAVE THESE INSTRUCTIONS  
6
 
FUNCTIONAL  
DESCRIPTION  
CAUTION:  
Always be sure that the tool is switched off and the  
battery cartridge is removed before adjusting or  
checking function on the tool.  
002045  
Installing or removing battery cartridge  
1
Always switch off the tool before insertion or removal of  
the battery cartridge.  
2
To remove the battery cartridge, pull out the set plate on  
the tool and grasp both sides of the cartridge while  
withdrawing it from the tool.  
To insert the battery cartridge, align the tongue on the  
battery cartridge with the groove in the housing and slip  
it into place. Snap the set plate back into place. Be sure  
to close the set plate fully before using the tool to prevent  
the battery cartridge from accidentally falling out of the  
tool.  
1. Set plate  
2. Battery cartridge  
Do not use force when inserting the battery cartridge. If  
the cartridge does not slide in easily, it is not being  
inserted correctly.  
002862  
Charging  
1. Plug the battery charger into the proper AC voltage  
source.  
1
2. Insert the battery cartridge so that the plus and minus  
terminals on the battery cartridge are on the same sides  
as their respective markings on the charger. Insert the  
cartridge fully into the port so that it rests on the charger  
port floor.  
1. Charging light  
3. When the battery cartridge is inserted, the charging light  
color will flash in red color and charging will begin.  
4. When the charging light goes out after about one hour,  
you may remove the fully charged battery cartridge.  
5. After charging, unplug the charger from the power  
source.  
NOTE:  
The battery charger is for charging Makita battery  
cartridge. Never use it for other purposes or for other  
manufacturers batteries.  
7
 
If you try to charge a battery cartridge from a just  
operated tool, sometimes the charging light will not  
come on. If this occurs, let the cartridge cool off for a  
while. Then re-insert it and try to charge it once more.  
When you charge a new battery cartridge or a battery  
cartridge which has not been used for a long period of  
time, it may not accept a full charge. This is a normal  
condition and does not indicate a problem. You can  
recharge the battery cartridge fully after discharging it  
completely and recharging a couple of times.  
When you charge a battery cartridge which has not been  
used for a long period, sometimes the charging light will  
go out soon. If this occurs, remove the battery cartridge  
and re-insert it. If the charging light goes out within one  
minute even after repeating this procedure a couple of  
times, the battery cartridge is dead. Replace it with a  
new one.  
If you wish to charge two battery cartridges, allow 15  
minutes between charging on the charger.  
Tips for maintaining maximum battery life  
1. Charge the battery cartridge before completely dis-  
charged.  
Always stop tool operation and charge the battery car-  
tridge when you notice less tool power.  
2. Never recharge a fully charged battery cartridge.  
Overcharging shortens the battery service life.  
3. Charge the battery cartridge with room temperature at  
10°C - 40°C (50°F - 104°F).  
Let a hot battery cartridge cool down before charging it.  
002863  
Switch action  
CAUTION:  
Before inserting the battery cartridge into the tool,  
always check to see that the switch trigger actuates  
properly and returns to the OFFposition when  
released.  
1
To start the tool, simply pull the switch trigger. Tool speed is  
increased by increasing pressure on the switch trigger.  
Release the switch trigger to stop.  
1. Switch trigger  
8
 
Electric brake  
This tool is equipped with an electric brake. If the tool consis-  
tently fails to quickly stop after switch trigger release, have  
tool serviced at a Makita service center.  
002071  
Reversing switch action  
1
This tool has a reversing switch to change the direction of  
rotation. Move the reversing switch lever to the A side for  
clockwise rotation or the B side for counterclockwise rotation.  
2
3
4
When the reversing switch lever is in the neutral position, the  
switch trigger cannot be pulled.  
CAUTION:  
1. Reversing switch lever  
2. Counter clockwise  
3. Clockwise  
Always check the direction of rotation before operation.  
Use the reversing switch only after the tool comes to a  
complete stop. Changing the direction of rotation before  
the tool stops may damage the tool.  
4. Switch trigger  
When not operating the tool, always set the reversing  
switch lever to the neutral position.  
002092  
Speed change  
1
2
3
To change the speed, first switch off the tool and then slide  
the speed change lever to the IIside for high speed or I”  
side for low speed. Be sure that the speed change lever is  
set to the correct position before operation. Use the right  
speed for your job.  
CAUTION:  
1. Low speed  
Always set the speed change lever fully to the correct  
position. If you operate the tool with the speed change  
lever positioned halfway between the Iside and II”  
side, the tool may be damaged.  
2. High speed  
3. Speed change lever  
Always make sure that the gear is engaged properly by  
running the tool under no load after sliding the speed  
change lever to the desired speed position. If you  
operate the tool with the gear engaged improperly, the  
tool may be damaged.  
Do not use the speed change lever while the tool is  
running. The tool may be damaged.  
9
 
002099  
Adjusting the fastening torque  
2
3
1
4
The fastening torque can be adjusted in 6 steps by turning  
the adjusting ring so that its graduations are aligned with the  
pointer on the tool body. The fastening torque is minimum  
when the number 1 is aligned with the pointer, and maximum  
when the  
marking is aligned with the pointer.  
The clutch will slip at various torque levels when set at the  
number 1 to 5. The clutch is designed not to slip at the  
marking.  
1. Pointer  
2. Weak  
3. Strong  
Before actual operation, drive a trial screw into your material  
or a piece of duplicate material to determine which torque  
level is required for a particular application.  
4. Torque adjusting ring  
NOTE:  
The adjusting ring does not lock when the pointer is  
positioned only halfway between the graduations.  
Do not operate the tool with the adjusting ring set  
between the number 5 and the marking. The tool may  
be damaged.  
ASSEMBLY  
CAUTION:  
Always be sure that the tool is switched off and the  
battery cartridge is removed before carrying out any  
work on the tool.  
002111  
Installing or removing driver bit or drill bit  
Hold the ring and turn the sleeve counterclockwise to open  
the chuck jaws. Place the bit in the chuck as far as it will go.  
Hold the ring firmly and turn the sleeve clockwise to tighten  
the chuck.  
2
1
3
To remove the bit, hold the ring and turn the sleeve counter-  
clockwise.  
1. Tighten  
2. Sleeve  
3. Ring  
When not using the driver bit, keep it in the bit holders. Bits  
45 mm (1-3/4) long can be kept there.  
OPERATION  
Screwdriving operation  
CAUTION:  
Adjust the adjusting ring to the proper torque level for  
your work.  
10  
 
Place the point of the driver bit in the screw head and apply  
pressure to the tool. Start the tool slowly and then increase  
the speed gradually. Release the switch trigger as soon as  
the clutch cuts in.  
NOTE:  
Make sure that the driver bit is inserted straight in the  
screw head, or the screw and/or bit may be damaged.  
When driving wood screws, predrill pilot holes to make  
driving easier and to prevent splitting of the workpiece.  
See the chart.  
Nominal diameter of  
wood screw (mm)  
3.1 (1/8)  
Recommended size  
of pilot hole (mm)  
2.0 - 2.2 (5/64- 3/32)  
2.2 - 2.5 (3/32- 3/32)  
2.5 - 2.8 (3/32- 7/64)  
2.9 - 3.2 (7/64- 1/8)  
3.1 - 3.4 (1/8- 9/64)  
3.3 - 3.6 (1/8- 9/64)  
3.5 (9/64)  
3.8 (5/32)  
4.5 (11/64)  
4.8 (3/16)  
5.1 (13/64)  
If the tool is operated continuously until the battery  
cartridge has discharged, allow the tool to rest for 15  
minutes before proceeding with a fresh battery.  
002137  
Drilling operation  
Drilling in wood  
When drilling in wood, the best results are obtained with  
wood drills equipped with a guide screw. The guide screw  
makes drilling easier by pulling the bit into the workpiece.  
Drilling in metal  
To prevent the bit from slipping when starting a hole, make  
an indentation with a center-punch and hammer at the point  
to be drilled. Place the point of the bit in the indentation and  
start drilling.  
Use a cutting lubricant when drilling metals. The exceptions  
are iron and brass which should be drilled dry.  
CAUTION:  
Pressing excessively on the tool will not speed up the  
drilling. In fact, this excessive pressure will only serve to  
damage the tip of your bit, decrease the tool  
performance and shorten the service life of the tool.  
11  
 
There is a tremendous force exerted on the tool/bit at the  
time of hole break through. Hold the tool firmly and exert  
care when the bit begins to break through the workpiece.  
A stuck bit can be removed simply by setting the  
reversing switch to reverse rotation in order to back out.  
However, the tool may back out abruptly if you do not  
hold it firmly.  
Always secure small workpieces in a vise or similar hold-  
down device.  
If the tool is operated continuously until the battery  
cartridge has discharged, allow the tool to rest for 15  
minutes before proceeding with a fresh battery.  
MAINTENANCE  
CAUTION:  
Always be sure that the tool is switched off and the  
battery cartridge is removed before attempting to  
perform inspection or maintenance.  
To maintain product SAFETY and RELIABILITY, repairs, any  
other maintenance or adjustment should be performed by  
Makita Authorized or Factory Service Centers, always using  
Makita replacement parts.  
EN0001-1  
Recycling the Battery  
The only way to dispose of a Makita battery is to recycle it.  
The law prohibits any other method of disposal.  
To recycle the battery:  
1. Remove the battery from the tool.  
Ni-Cd  
2. a) Take the battery to your nearest Makita Factory Ser-  
vice Center  
or  
b) Take the battery to your nearest Makita Authorized  
Service Center or Distributor that has been desig-  
nated as a Makita battery recycling location.  
Call your nearest Makita Service Center or Distributor to  
determine the location that provides Makita battery recycling.  
See your local Yellow Pages under “Tools-Electric”.  
12  
 
ACCESSORIES  
CAUTION:  
These accessories or attachments are recommended for  
use with your Makita tool specified in this manual. The  
use of any other accessories or attachments might  
present a risk of injury to persons. Only use accessory  
or attachment for its stated purpose.  
If you need any assistance for more details regarding these  
accessories, ask your local Makita service center.  
Drill bits  
Screw bits  
Various type of Makita genuine batteries and chargers  
Rubber pad assembly  
Wool bonnet  
Foam polishing pad  
Plastic carrying case  
13  
 
Memo  
14  
 
Memo  
15  
 
Memo  
16  
 
First-Class  
Postage  
Required  
Post Office will  
not deliver  
without proper  
postage.  
Makita U.S.A., Inc.  
14930 Northam Street  
La Mirada, CA 90638-5753  
Fold  
 
MAIL THIS PORTION  
Your answers to the following questions are appreciated.  
1.This product was purchased from:  
3. How did you learn about this product:  
Home Center  
Other (  
)
Magazine  
Radio  
Hardware/Lumber Store  
Tool Distributor  
From Dealer  
Newspaper  
Store Display  
Catalog  
Exhibition  
From Friend  
Previous Usage  
Other (  
Industrial Supply  
Construction Supply  
)
2. Use of the product is intended for:  
4. Most favored points are:  
Construction Trade  
Industrial Maintenance  
Home Maintenance  
Hobby  
Design  
Repair Service  
Durability  
Power  
Features  
Size  
Price  
Other (  
)
Other (  
)
Makita Brand  
5. Any comments:  
DATE PURCHASED  
MONTH  
MODEL NO.  
DAY  
YEAR  
SERIAL NO.  
STATUS  
SEX  
Married Single  
M
F
INTL.  
LAST NAME / COMPANY NAME  
STREET ADRESS  
CITY  
AREA  
CODE  
STATE  
ZIP CODE  
PHONE  
40-49  
Under 19  
20-29  
30-39  
50-60  
Over 60  
AGE:  
BE SURE TO COMPLETE THE CUSTOMERS PORTION OF THIS FORM AND RETAIN FOR YOUR RECORDS.  
Please return this portion by facsimile or mail.  
Facsimile No: (714) 522-8133  
 
Paste  
Paste  
Paste  
Paste  
Paste  
Paste  
Paste  
Paste  
FACTORY SERVICE CENTERS  
1-800-4-MAKITA  
RETAIN THIS PORTION FOR YOUR RECORDS  
ALABAMA  
COLORADO  
KENTUCKY  
NEW MEXICO  
PUERTO RICO  
2365 Pelham Parkway  
Pelham, AL 35124  
(205) 620-1791  
11839 E. 51st Ave.  
Denver, CO 80239-2709  
(303) 371-2850  
1215 S. Hurstbourne Parkway  
Louisville, KY 40222  
(502) 326-3740  
5805 Menaul Blvd. NE  
Albuquerque, NM 87110  
(505) 881-4619  
200 Guayama St.  
Hato Rey, PR 00917  
(787) 250-8776  
ARIZONA  
CONNECTICUT  
508 Spring St.  
Windsor Locks, CT 06096  
(860) 292-6405  
LOUSIANA  
NEWYORK  
TENNESSEE  
3707 E. Broadway Rd., Ste. 6  
Phoenix, AZ 85040  
(602) 437-2850  
5626 Jefferson Hwy.  
Harahan, LA 70123  
(504) 733-4138  
4917 Genessee Street  
Cheektowaga, NY 14225  
(716) 685-9503  
4655 Nolensville Rd.  
Nashville, TN 37211  
(615) 331-9922  
131-35 31st Ave.  
Flushing, NY 11354  
(718) 886-0971  
ARKANSAS  
FLORIDA  
MARYLAND  
TEXAS  
Shackleford Shopping Center  
240 South Shackleford Rd.,  
Ste. C  
620 Douglas Ave. Suite 1302  
Altamonte Springs, FL 32714  
(407) 774-6000  
7541 - 45 Ritchie Highway  
Glen Burnie, MD 21061  
(410) 590-0160  
12801 Stemmons Fwy Ste. 809  
Farmers Branch, TX 75234  
(972) 243-1150  
Little Rock, AR 72211  
(501) 224-5733  
NORTH CAROLINA  
3501-G S. Tryon St.  
Charlotte, NC 28217  
(704) 527-0611  
750 East Sample Road  
Pompano Beach, FL 33064  
(954) 781-6333  
12701 Directors Dr.  
Stafford, TX 77477-3701  
(281) 565-8665  
MASSACHUSETTS  
232 Providence Hwy.  
Westwood, MA 02090  
(617) 461-9754  
CALIFORNIA  
41850 Christy St.  
Fremont, CA 94538-5107  
(510) 657-9881  
Thompson Center Waters  
5501 W. Waters Ave., Ste. 406  
Tampa, FL 33634  
3453 IH-35 North, Ste. 101  
San Antonio, TX 78219  
(210) 228-0676  
OHIO  
6253 E. Main St.  
Columbus, OH 43213  
(614) 860-0222  
(813) 886-8292  
MICHIGAN  
1421 N. Clovis Ave., Ste. 112  
Fresno, CA 93727  
(559) 252-5166  
37454 Ann Arbor Trail  
Livonia, MI 48150  
(313) 432-1012  
UTAH  
GEORGIA  
6379 Pearl Road  
Parma Heights, OH 44130  
(440) 843-7555  
145 E. 1300 S., Ste. 101  
Salt Lake City, UT 84115  
(801) 359-3410  
4680 River Green Parkway  
Duluth, GA 30096-2566  
(770) 476-8911  
14930 Northam St.  
La Mirada, CA 90638-5753  
(714) 522-8088  
MINNESOTA  
6427 Penn Ave. South  
Richfield, MN 55423  
(612) 869-5199  
1617 E. Kemper Rd.  
Sharonville, OH 45246  
(513) 771-0788  
VIRGINIA  
5760 Northampton Blvd,. Ste.  
102  
Virginia Beach, VA 23455  
(757) 460-0280  
1970 Fulton Avenue  
Sacramento, CA 95825  
(916) 482-5197  
HAWAII  
4510 Salt Lake Blvd., Suite A7  
Honolulu, HI 96818  
(808) 847-0038  
MISSOURI  
OKLAHOMA  
1440 South EStreet  
San Bernardino, CA 92408  
(909) 885-1289  
9876 Watson Road  
St. Louis, MO 63126-2221  
(314) 909-9889  
552 E. Memorial Road  
Oklahoma City, OK 73114  
(405) 752-2655  
ILLINOIS  
WASHINGTON  
1450 Feehanville Dr.  
Mt. Prospect, IL 60056-6011  
(847) 297-3100  
22220 84th Ave. So., Bldg. A  
Kent, WA 98032  
(253) 395-8055  
7674 Clairemont Mesa Blvd.  
San Diego, CA 92111  
(858) 278-4471  
NEBRASKA  
OREGON  
4129 S. 84th St.  
Omaha, NE 68127  
(402) 597-2925  
828 19th Avenue., N.W.  
Portland, OR 97209  
(503) 222-1823  
1714 E.McFadden Ave., Unit M  
Santa Ana, CA 92705  
(714) 667-5066  
INDIANA  
WISCONSIN  
8403 Michigan Road, Unit 1  
Indianapolis, IN 46268  
(317) 334-9980  
Lincoln Plaza Shopping Ctr.  
2245 S. 108th St. West Allis, WI  
53227  
NEVADA  
3375 S. Decatur Blvd.  
Suites. 22 - 24  
Las Vegas, NV 89102  
(702) 368-4277  
PENNSYLVANIA  
Springwater Plaza  
364 Wilmington W. Chester  
Pike  
Glen Mills, PA 19342  
(610) 459-4122  
1565 Winchester B.  
Campbell, CA 95008-0501  
(408) 379-0377  
(414) 541-4776  
KANSAS  
8819 W. 95th St.  
Overland Park, KS 66212  
(913) 642-1111  
16735 Saticoy St., Ste. 105  
Van Nuys, CA 91406  
(818) 782-2440  
NEW JERSEY  
6200 Babcock Blvd  
Pittsburgh, PA 15237  
(412) 366-6363  
251 Herrod Blvd.  
Dayton, NJ 08810-1539  
(609) 655-1212  
CUSTOMERS RECORD  
Date Purchased  
When you need service: Send  
complete tool (prepaid) to one  
of the Makita Factory Service  
Centers listed, or to an Authorized  
Makita Service Center. Be sure  
to attach a letter to the outside of  
the carton detailing the problem  
with your tool.  
Dealers Name & Address  
Model No.  
Serial No.  
19  
 
WARNING  
Some dust created by power sanding, sawing, grinding, drilling, and other  
construction activities contains chemicals known to the State of California  
to cause cancer, birth defects or other reproductive harm. Some examples  
of these chemicals are:  
lead from lead-based paints,  
crystalline silica from bricks and cement and other masonry products, and  
arsenic and chromium from chemically-treated lumber.  
Your risk from these exposures varies, depending on how often you do this  
type of work. To reduce your exposure to these chemicals: work in a well  
ventilated area, and work with approved safety equipment, such as those  
dust masks that are specially designed to filter out microscopic particles.  
MAKITA LIMITED ONE YEAR WARRANTY  
Warranty Policy  
Every Makita tool is thoroughly inspected and tested before leaving the factory. It is warranted to be free of  
defects from workmanship and materials for the period of ONE YEAR from the date of original purchase.  
Should any trouble develop during this one-year period, return the COMPLETE tool, freight prepaid, to one of  
Makita's Factory or Authorized Service Centers. If inspection shows the trouble is caused by defective  
workmanship or material, Makita will repair (or at our option, replace) without charge.  
This Warranty does not apply where:  
repairs have been made or attempted by others:  
repairs are required because of normal wear and tear:  
the tool has been abused, misused or improperly maintained:  
alterations have been made to the tool.  
IN NO EVENT SHALL MAKITA BE LIABLE FOR ANY INDIRECT, INCIDENTAL OR CONSEQUENTIAL  
DAMAGES FROM THE SALE OR USE OF THE PRODUCT. THIS DISCLAIMER APPLIES BOTH DURING  
AND AFTER THE TERM OF THIS WARRANTY.  
MAKITA DISCLAIMS LIABILITY FOR ANY IMPLIED WARRANTIES, INCLUDING IMPLIED WARRANTIES OF  
"MERCHANTABILITY" AND "FITNESS FOR A SPECIFIC PURPOSE," AFTER THE ONE-YEAR TERM OF  
THIS WARRANTY.  
This Warranty gives you specific legal rights, and you may also have other rights which vary form state to state.  
Some states do not allow the exclusion or limitation of incidental or consequential damages, so the above  
limitation or exclusion may not apply to you. Some states do not allow limitation on how long an implied  
warranty lasts, so the above limitation may not apply to you.  
MAKITA MANUFACTURING EUROPE LTD  
ROAD 7, HORTONWOOD INDUSTRIAL ESTATE  
TELFORD, SHROPSHIRE TF1 4GP, ENGLAND  
884084E066  
 

Lasko Patio Heater 6251 User Manual
Life Fitness Elliptical Trainer 8973801 REV B 3 User Manual
Lincoln Electric Welder 250FG User Manual
Lindy Computer Hardware 70543 User Manual
Lindy Computer Monitor 25021 User Manual
Linksys Switch EZXS55W v2 User Manual
Marshall electronic Microphone V67I User Manual
McCulloch Brush Cutter MAC 250 B User Manual
Melissa Electric Heater 670 203 User Manual
Mellerware Iron 23455 User Manual